{"id":1162,"date":"2012-12-29T14:20:23","date_gmt":"2012-12-29T19:20:23","guid":{"rendered":"http:\/\/www.leucht.com\/blog\/?p=1162"},"modified":"2016-04-29T12:04:57","modified_gmt":"2016-04-29T16:04:57","slug":"custom-built-wood-washer-and-dryer-shelves","status":"publish","type":"post","link":"http:\/\/www.leucht.com\/blog\/2012\/12\/custom-built-wood-washer-and-dryer-shelves\/","title":{"rendered":"Custom built wood washer and dryer shelves"},"content":{"rendered":"

Ever since we got our front loading washer and dryer a few years ago, we’ve been wanting to get some of those laundry pedestals to lift them up higher.\u00a0 But the pedestal units are pretty pricey.\u00a0 Those things are like $250 bucks … each<\/a>.\u00a0 Ridiculous. So I decided I would make my own laundry pedestals out of wood that I had laying around in my shop.\u00a0 And I decided that I would design a pedestal that would include both a step stool and a storage drawer in one single unit. The step stool will help us reach the wall mounted cabinets that are mounted above our washer and dryer.<\/p>\n

Click on any photo to view larger versions of it in my photo gallery.<\/p>\n

Here is a photo of the basic frame for my pedestal design.\u00a0 You can see that the front (facing down and to the left) is basically open to receive a drawer.\u00a0 The sides and back are solid enough to support a few hundred pounds (as long as the weight is directed down into the floor and focused at the four corners).\u00a0 All the cross beams are just there for stability.\u00a0 The four feet of the washer or dryer sit on the top-most two 2x4s.<\/p>\n

\"\"<\/a><\/p>\n

Here is the same basic frame after the decorative plywood and trim was applied.\u00a0 The back of the unit was left open and so was the top.\u00a0 That should allow for access to the bottom of the washer or dryer and access behind the unit if that access is ever needed.<\/p>\n

\"\"<\/a><\/p>\n

I forgot to take photos of the drawer unit during construction, but this photo gives you a pretty good idea of it’s design.\u00a0 It’s fairly straightforward.\u00a0 The front of the drawer is on the upper left in this photo and contains the step stool portion which is made from 2x4s for strength.\u00a0 The horizontal 2×4 in the middle is both for stability and for mounting the pull handle.\u00a0 The rest of the drawer is made from plywood that I joined together with biscuit joints.\u00a0 The 4th sidewall is missing from this photo, but it fits right over the exposed 2x4s shown in this photo and creates a completely closed drawer bin used for storage.<\/p>\n

\"\"<\/a><\/p>\n

Here is the same drawer from another angle.\u00a0 The front of the drawer has the decorative plywood.<\/p>\n

\"\"<\/a><\/p>\n

And here is what the unit looks like with the drawer installed.\u00a0 I chose not to install a drawer slide.\u00a0 I just installed some felt pads underneath the drawer unit and it slides in and out just fine.\u00a0 The next step is to prime and paint to match the washer and dryer.<\/p>\n

\"\"<\/a><\/p>\n

And here is what the finished laundry pedestal looks like in use in our laundry room.\u00a0 The drawer holds quite a bit of stuff and pulls out much farther than is shown in the photo below.<\/p>\n

\"\"<\/a><\/p>\n

And the step-stool feature allows us to reach the wall mounted cabinets above our washer and dryer.<\/p>\n

\"\"<\/a><\/p>\n

That\u2019s about all the detail that I can think of.\u00a0 Add a comment below if you like this design or if you have any questions about details that I have left out.\u00a0 If you end up using my design for a laundry pedestal or if you have an ideas for improvements, please feel free to post in the comments below.<\/p>\n

Kurt<\/p>\n","protected":false},"excerpt":{"rendered":"

Ever since we got our front loading washer and dryer a few years ago, we’ve been wanting to get some of those laundry pedestals to lift them up higher.\u00a0 But the pedestal units are pretty pricey.\u00a0 Those things are like $250 bucks … each.\u00a0 Ridiculous. So I decided I would make my own laundry pedestals […]<\/p>\n","protected":false},"author":2,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[106,107,112],"tags":[45,206,205,43,15],"_links":{"self":[{"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/posts\/1162"}],"collection":[{"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/comments?post=1162"}],"version-history":[{"count":17,"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/posts\/1162\/revisions"}],"predecessor-version":[{"id":2437,"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/posts\/1162\/revisions\/2437"}],"wp:attachment":[{"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/media?parent=1162"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/categories?post=1162"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.leucht.com\/blog\/wp-json\/wp\/v2\/tags?post=1162"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}